Using netconsole netpoll_poll_dev could be called from interrupt
context, thus using disable_irq() would cause the following kernel
warning with CONFIG_DEBUG_ATOMIC_SLEEP enabled:
BUG: sleeping function called from invalid context at kernel/irq/manage.c:137
in_atomic(): 1, irqs_disabled(): 128, non_block: 0, pid: 10, name: ksoftirqd/0
CPU: 0 PID: 10 Comm: ksoftirqd/0 Tainted: G W 5.15.42-00075-g816b502b2298-dirty #117
Hardware name: aml (r1) (DT)
Call trace:
dump_backtrace+0x0/0x270
show_stack+0x14/0x20
dump_stack_lvl+0x8c/0xac
dump_stack+0x18/0x30
___might_sleep+0x150/0x194
__might_sleep+0x64/0xbc
synchronize_irq+0x8c/0x150
disable_irq+0x2c/0x40
stmmac_poll_controller+0x140/0x1a0
netpoll_poll_dev+0x6c/0x220
netpoll_send_skb+0x308/0x390
netpoll_send_udp+0x418/0x760
write_msg+0x118/0x140 [netconsole]
console_unlock+0x404/0x500
vprintk_emit+0x118/0x250
dev_vprintk_emit+0x19c/0x1cc
dev_printk_emit+0x90/0xa8
__dev_printk+0x78/0x9c
_dev_warn+0xa4/0xbc
ath10k_warn+0xe8/0xf0 [ath10k_core]
ath10k_htt_txrx_compl_task+0x790/0x7fc [ath10k_core]
ath10k_pci_napi_poll+0x98/0x1f4 [ath10k_pci]
__napi_poll+0x58/0x1f4
net_rx_action+0x504/0x590
_stext+0x1b8/0x418
run_ksoftirqd+0x74/0xa4
smpboot_thread_fn+0x210/0x3c0
kthread+0x1fc/0x210
ret_from_fork+0x10/0x20
Since [0] .ndo_poll_controller is only needed if driver doesn't or
partially use NAPI. Because stmmac does so, stmmac_poll_controller
can be removed fixing the above warning.
[0] commit ac3d9dd034 ("netpoll: make ndo_poll_controller() optional")
Cc: <stable@vger.kernel.org> # 5.15.x
Fixes: 47dd7a540b ("net: add support for STMicroelectronics Ethernet controllers")
Signed-off-by: Remi Pommarel <repk@triplefau.lt>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/1c156a6d8c9170bd6a17825f2277115525b4d50f.1696429960.git.repk@triplefau.lt
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The STM32MP1 keeps clk_rx enabled during suspend, and therefore the
driver does not enable the clock in stm32_dwmac_init() if the device was
suspended. The problem is that this same code runs on STM32 MCUs, which
do disable clk_rx during suspend, causing the clock to never be
re-enabled on resume.
This patch adds a variant flag to indicate that clk_rx remains enabled
during suspend, and uses this to decide whether to enable the clock in
stm32_dwmac_init() if the device was suspended.
This approach fixes this specific bug with limited opportunity for
unintended side-effects, but I have a follow up patch that will refactor
the clock configuration and hopefully make it less error prone.
Fixes: 6528e02cc9 ("net: ethernet: stmmac: add adaptation for stm32mp157c.")
Signed-off-by: Ben Wolsieffer <ben.wolsieffer@hefring.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Link: https://lore.kernel.org/r/20230927175749.1419774-1-ben.wolsieffer@hefring.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
commit 133466c3bb ("net: stmmac: use per-queue 64 bit statistics
where necessary") caused one regression as found by Uwe, the backtrace
looks like:
INFO: trying to register non-static key.
The code is fine but needs lockdep annotation, or maybe
you didn't initialize this object before use?
turning off the locking correctness validator.
CPU: 0 PID: 1 Comm: swapper/0 Not tainted 6.5.0-rc1-00449-g133466c3bbe1-dirty #21
Hardware name: STM32 (Device Tree Support)
unwind_backtrace from show_stack+0x18/0x1c
show_stack from dump_stack_lvl+0x60/0x90
dump_stack_lvl from register_lock_class+0x98c/0x99c
register_lock_class from __lock_acquire+0x74/0x293c
__lock_acquire from lock_acquire+0x134/0x398
lock_acquire from stmmac_get_stats64+0x2ac/0x2fc
stmmac_get_stats64 from dev_get_stats+0x44/0x130
dev_get_stats from rtnl_fill_stats+0x38/0x120
rtnl_fill_stats from rtnl_fill_ifinfo+0x834/0x17f4
rtnl_fill_ifinfo from rtmsg_ifinfo_build_skb+0xc0/0x144
rtmsg_ifinfo_build_skb from rtmsg_ifinfo+0x50/0x88
rtmsg_ifinfo from __dev_notify_flags+0xc0/0xec
__dev_notify_flags from dev_change_flags+0x50/0x5c
dev_change_flags from ip_auto_config+0x2f4/0x1260
ip_auto_config from do_one_initcall+0x70/0x35c
do_one_initcall from kernel_init_freeable+0x2ac/0x308
kernel_init_freeable from kernel_init+0x1c/0x138
kernel_init from ret_from_fork+0x14/0x2c
The reason is the rxq|txq_stats structures are not what expected
because stmmac_open() -> __stmmac_open() the structure is overwritten
by "memcpy(&priv->dma_conf, dma_conf, sizeof(*dma_conf));"
This causes the well initialized syncp member of rxq|txq_stats is
overwritten unexpectedly as pointed out by Johannes and Uwe.
Fix this issue by moving rxq|txq_stats back to stmmac_extra_stats. For
SMP cache friendly, we also mark stmmac_txq_stats and stmmac_rxq_stats
as ____cacheline_aligned_in_smp.
Fixes: 133466c3bb ("net: stmmac: use per-queue 64 bit statistics where necessary")
Signed-off-by: Jisheng Zhang <jszhang@kernel.org>
Reported-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Tested-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230917165328.3403-1-jszhang@kernel.org
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Setting ethtool -C eth0 tx-usecs 0 is supposed to disable the use of the
coalescing timer but currently it gets programmed with zero delay
instead.
Disable the use of the coalescing timer if tx-usecs is zero by
preventing it from being restarted. Note that to keep things simple we
don't start/stop the timer when the coalescing settings are changed, but
just let that happen on the next transmit or timer expiry.
Fixes: 8fce333170 ("net: stmmac: Rework coalesce timer and fix multi-queue races")
Signed-off-by: Vincent Whitchurch <vincent.whitchurch@axis.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Clarify the difference between "interface" and "phy_interface" in
struct plat_stmmacenet_data, both by adding a comment, and also
renaming "interface" to be "mac_interface". The difference between
these are:
MAC ----- optional PCS ----- SerDes ----- optional PHY ----- Media
^ ^
mac_interface phy_interface
Note that phylink currently only deals with phy_interface.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://lore.kernel.org/r/E1qZq83-005tts-6K@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
We have a local variable for priv->plat->mdio_bus_data, which we use
later in the conditional if() block, but we evaluate the above within
the conditional expression. Use mdio_bus_data instead. Since these
will be the only two users of this local variable, move its assignment
just before the if().
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://lore.kernel.org/r/E1qZAXJ-005pU1-1z@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
1. XGMAC Core does not have hash_filter definition, it uses
vlhash(VLAN Hash Filtering) instead, skip hash_filter when XGMAC.
2. Show exact size of Hash Table instead of raw register value.
3. Show full description of safety features defined by Synopsys Databook.
4. When safety feature is configured with no parity, or ECC only,
keep FSM Parity Checking disabled.
Signed-off-by: Furong Xu <0x1207@gmail.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
All captured timestamps should be corrected by PHY, MAC and CDC introduced
latency/errors. The CDC correction is already used. Enable MAC propagation delay
correction as well which is available since commit 26cfb838aa ("net: stmmac:
correct MAC propagation delay").
Before:
|ptp4l[390.458]: rms 7 max 21 freq +177 +/- 14 delay 357 +/- 1
After:
|ptp4l[620.012]: rms 7 max 20 freq +195 +/- 14 delay 345 +/- 1
Tested on Intel Elkhart Lake.
Signed-off-by: Kurt Kanzenbach <kurt@linutronix.de>
Reviewed-by: Johannes Zink <j.zink@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
1. Show TSSTSSEL(Timestamp System Time Source),
ADDMACADRSEL(additional MAC addresses), SMASEL(SMA/MDIO Interface),
HDSEL(Half-duplex Support) in debugfs.
2. Show exact number of additional MAC address registers for XGMAC2 core.
3. XGMAC2 core does not have different IP checksum offload types, so just
show rx_coe instead of rx_coe_type1 or rx_coe_type2.
4. XGMAC2 core does not have rxfifo_over_2048 definition, skip it.
Signed-off-by: Furong Xu <0x1207@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When using a fixed-link setup, certain devices like the SJA1105 require a
small pause in the TXC clock line to enable their internal tunable
delay line (TDL).
To satisfy this requirement, this patch temporarily disables the TX clock,
and restarts it after a required period. This provides the required
silent interval on the clock line for SJA1105 to complete the frequency
transition and enable the internal TDLs. This action occurs before the link
is built up, so it does not impact a normal device too. There is no
need to identify if the connected device is an SJA1105 alike or not during
the implementation.
So far we have only enabled this feature on the i.MX93 platform.
Signed-off-by: Shenwei Wang <shenwei.wang@nxp.com>
Reviewed-by: Frank Li <frank.li@nxp.com>
Link: https://lore.kernel.org/r/20230807160716.259072-3-shenwei.wang@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
As the i.MX8MP supports reading MAC propagation delay and correcting the
Hardware timestamp counter for additional delays [1], enable the feature
for this SoC.
This reduces phase error of the PPS output from the PTP Hardware Clock
from approx 150ns to 100ns.
[1] i.MX8MP Reference Manual, rev.1 Section 11.7.2.5.3 "Timestamp
correction"
Signed-off-by: Johannes Zink <j.zink@pengutronix.de>
Link: https://lore.kernel.org/r/20230719-stmmac_correct_mac_delay-v3-2-61e63427735e@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The IEEE1588 Standard specifies that the timestamps of Packets must be
captured when the PTP message timestamp point (leading edge of first
octet after the start of frame delimiter) crosses the boundary between
the node and the network. As the MAC latches the timestamp at an
internal point, the captured timestamp must be corrected for the
additional data transmission latency, as described in the publicly
available datasheet [1].
This patch only corrects for the MAC-Internal delay, which can be read
out from the MAC_Ingress_Timestamp_Latency register on DWMAC version 5,
since the Phy framework currently does not support querying the Phy
ingress and egress latency. The Closs Domain Crossing Circuits errors as
indicated in [1] are already being accounted in the
stmmac_get_tx_hwtstamp() function and are not corrected here.
As the Latency varies for different link speeds and MII
modes of operation, the correction value needs to be updated on each
link state change.
As the delay also causes a phase shift in the timestamp counter compared
to the rest of the network, this correction will also reduce phase error
when generating PPS outputs from the timestamp counter.
Since the correction registers may be unavailable on some hardware and
no feature bits are documented for dynamically detection of the MAC
propagation delay readout, introduce a feature bit to explicitely enable
MAC delay Correction in the gluecode driver.
[1] i.MX8MP Reference Manual, rev.1 Section 11.7.2.5.3 "Timestamp
correction"
Signed-off-by: Johannes Zink <j.zink@pengutronix.de>
Link: https://lore.kernel.org/r/20230719-stmmac_correct_mac_delay-v2-1-3366f38ee9a6@pengutronix.de
Link: https://lore.kernel.org/r/20230719-stmmac_correct_mac_delay-v3-1-61e63427735e@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Martin KaFai Lau says:
====================
pull-request: bpf-next 2023-08-03
We've added 54 non-merge commits during the last 10 day(s) which contain
a total of 84 files changed, 4026 insertions(+), 562 deletions(-).
The main changes are:
1) Add SO_REUSEPORT support for TC bpf_sk_assign from Lorenz Bauer,
Daniel Borkmann
2) Support new insns from cpu v4 from Yonghong Song
3) Non-atomically allocate freelist during prefill from YiFei Zhu
4) Support defragmenting IPv(4|6) packets in BPF from Daniel Xu
5) Add tracepoint to xdp attaching failure from Leon Hwang
6) struct netdev_rx_queue and xdp.h reshuffling to reduce
rebuild time from Jakub Kicinski
* tag 'for-netdev' of https://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpf-next: (54 commits)
net: invert the netdevice.h vs xdp.h dependency
net: move struct netdev_rx_queue out of netdevice.h
eth: add missing xdp.h includes in drivers
selftests/bpf: Add testcase for xdp attaching failure tracepoint
bpf, xdp: Add tracepoint to xdp attaching failure
selftests/bpf: fix static assert compilation issue for test_cls_*.c
bpf: fix bpf_probe_read_kernel prototype mismatch
riscv, bpf: Adapt bpf trampoline to optimized riscv ftrace framework
libbpf: fix typos in Makefile
tracing: bpf: use struct trace_entry in struct syscall_tp_t
bpf, devmap: Remove unused dtab field from bpf_dtab_netdev
bpf, cpumap: Remove unused cmap field from bpf_cpu_map_entry
netfilter: bpf: Only define get_proto_defrag_hook() if necessary
bpf: Fix an array-index-out-of-bounds issue in disasm.c
net: remove duplicate INDIRECT_CALLABLE_DECLARE of udp[6]_ehashfn
docs/bpf: Fix malformed documentation
bpf: selftests: Add defrag selftests
bpf: selftests: Support custom type and proto for client sockets
bpf: selftests: Support not connecting client socket
netfilter: bpf: Support BPF_F_NETFILTER_IP_DEFRAG in netfilter link
...
====================
Link: https://lore.kernel.org/r/20230803174845.825419-1-martin.lau@linux.dev
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
For XGMAC versions < 2.2 number of supported mdio C22 addresses is
restricted to 3. From XGMAC version 2.2 there are no restrictions on
the C22 addresses, it supports all valid mdio addresses(0 to 31).
Signed-off-by: Rohan G Thomas <rohan.g.thomas@intel.com>
Acked-by: Jose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The clock data is an array of struct clk_bulk_data, so make sure to
allocate enough memory.
Fixes: d8ca113724 ("net: stmmac: tegra: Add MGBE support")
Signed-off-by: Thierry Reding <treding@nvidia.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The DT of_device.h and of_platform.h date back to the separate
of_platform_bus_type before it as merged into the regular platform bus.
As part of that merge prepping Arm DT support 13 years ago, they
"temporarily" include each other. They also include platform_device.h
and of.h. As a result, there's a pretty much random mix of those include
files used throughout the tree. In order to detangle these headers and
replace the implicit includes with struct declarations, users need to
explicitly include the correct includes.
Acked-by: Alex Elder <elder@linaro.org>
Reviewed-by: Bhupesh Sharma <bhupesh.sharma@linaro.org>
Reviewed-by: Wei Fang <wei.fang@nxp.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Link: https://lore.kernel.org/r/20230727014944.3972546-1-robh@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Qualcomm clocks can set their frequency to a variety of levels
generally. Let's use the max for clk_ptp_ref to ensure the best
timestamping resolution possible.
Without this, the default value of the clock is used. For sa8775p-ride
this is 19.2 MHz, far less than the 230.4 MHz possible.
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Andrew Halaney <ahalaney@redhat.com>
Link: https://lore.kernel.org/r/20230725211853.895832-4-ahalaney@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The IEEE1588 Standard specifies that the timestamps of Packets must be
captured when the PTP message timestamp point (leading edge of first
octet after the start of frame delimiter) crosses the boundary between
the node and the network. As the MAC latches the timestamp at an
internal point, the captured timestamp must be corrected for the
additional path latency, as described in the publicly available
datasheet [1].
This patch only corrects for the MAC-Internal delay, which can be read
out from the MAC_Ingress_Timestamp_Latency register, since the Phy
framework currently does not support querying the Phy ingress and egress
latency. The Closs Domain Crossing Circuits errors as indicated in [1]
are already being accounted in the stmmac_get_tx_hwtstamp() function and
are not corrected here.
As the Latency varies for different link speeds and MII
modes of operation, the correction value needs to be updated on each
link state change.
As the delay also causes a phase shift in the timestamp counter compared
to the rest of the network, this correction will also reduce phase error
when generating PPS outputs from the timestamp counter.
[1] i.MX8MP Reference Manual, rev.1 Section 11.7.2.5.3 "Timestamp
correction"
Signed-off-by: Johannes Zink <j.zink@pengutronix.de>
Link: https://lore.kernel.org/r/20230719-stmmac_correct_mac_delay-v2-1-3366f38ee9a6@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
commit a3a57bf07d ("net: stmmac: work
around sporadic tx issue on link-up") worked around a problem with TX
sometimes not working after a link-up by avoiding a redundant write to
MAC_CTRL_REG (aka GMAC_CONFIG), since the IP appeared to have problems
with handling multiple writes to that register in some cases.
That commit however only added the work around to dwmac_lib.c (apart
from the common code in stmmac_main.c), but my systems with version
4.21a of the IP exhibit the same problem, so add the work around to
dwmac4_lib.c too.
Fixes: a3a57bf07d ("net: stmmac: work around sporadic tx issue on link-up")
Signed-off-by: Vincent Whitchurch <vincent.whitchurch@axis.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Link: https://lore.kernel.org/r/20230721-stmmac-tx-workaround-v1-1-9411cbd5ee07@axis.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Currently, there are two major issues with stmmac driver statistics
First of all, statistics in stmmac_extra_stats, stmmac_rxq_stats
and stmmac_txq_stats are 32 bit variables on 32 bit platforms. This
can cause some stats to overflow after several minutes of
high traffic, for example rx_pkt_n, tx_pkt_n and so on.
Secondly, if HW supports multiqueues, there are frequent cacheline
ping pongs on some driver statistic vars, for example, normal_irq_n,
tx_pkt_n and so on. What's more, frequent cacheline ping pongs on
normal_irq_n happens in ISR, this makes the situation worse.
To improve the driver, we convert those statistics to 64 bit, implement
ndo_get_stats64 and update .get_ethtool_stats implementation
accordingly. We also use per-queue statistics where necessary to remove
the cacheline ping pongs as much as possible to make multiqueue
operations faster. Those statistics which are not possible to overflow
and not frequently updated are kept as is.
Signed-off-by: Jisheng Zhang <jszhang@kernel.org>
Link: https://lore.kernel.org/r/20230717160630.1892-3-jszhang@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Get the exact count of L3L4 filters when the L3L4FNUM field of
HW_FEATURE1 register is >= 8. If L3L4FNUM < 8, then the number of L3L4
filters supported by XGMAC is equal to L3L4FNUM. From L3L4FNUM >= 8
the number of L3L4 filters goes on like 8, 16, 32, ... Current
maximum of L3L4FNUM = 10.
Also, fix the XGMAC_IDDR bitmask of L3L4_ADDR_CTRL register. IDDR
field starts from the 8th bit of the L3L4_ADDR_CTRL register. IDDR[3:0]
indicates the type of L3L4 filter register while IDDR[8:4] indicates
the filter number (0 to 31). So overall 9 bits are used for IDDR
(i.e. L3L4_ADDR_CTRL[16:8]) to address the registers of all the
filters. Currently, XGMAC_IDDR is GENMASK(15,8), causing issues
accessing L3L4 filters above 15 for those XGMACs configured with more
than 16 L3L4 filters.
Signed-off-by: Rohan G Thomas <rohan.g.thomas@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
