The LTC4282 hot swap controller allows a board to be safely inserted and
removed from a live backplane. Using one or more external N-channel pass
transistors, board supply voltage and inrush current are ramped up at an
adjustable rate. An I2C interface and onboard ADC allows for monitoring
of board current, voltage, power, energy and fault status.
Signed-off-by: Nuno Sa <nuno.sa@analog.com>
Link: https://lore.kernel.org/r/20240129-b4-ltc4282-support-v4-3-fe75798164cc@analog.com
[groeck: clamp value range in ltc4282_write_voltage_byte_cached()]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
This driver exposes hardware sensors of the Gigabyte AORUS Waterforce
all-in-one CPU liquid coolers, which communicate through a proprietary
USB HID protocol. Report offsets were initially discovered in [1] and
confirmed by me on a Waterforce X240 by observing the sent reports from
the official software.
Available sensors are pump and fan speed in RPM, as well as coolant
temperature. Also available through debugfs is the firmware version.
Attaching a fan is optional and allows it to be controlled from the
device. If it's not connected, the fan-related sensors will report
zeroes.
The addressable RGB LEDs and LCD screen are not supported in this
driver and should be controlled through userspace tools.
[1]: https://github.com/liquidctl/liquidctl/issues/167
Signed-off-by: Aleksa Savic <savicaleksa83@gmail.com>
Link: https://lore.kernel.org/r/20231207122402.107032-1-savicaleksa83@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add support for LTC2991 Octal I2C Voltage, Current, and Temperature
Monitor.
The LTC2991 is used to monitor system temperatures, voltages and
currents. Through the I2C serial interface, the eight monitors can
individually measure supply voltages and can be paired for
differential measurements of current sense resistors or temperature
sensing transistors. Additional measurements include internal
temperature and internal VCC.
Signed-off-by: Antoniu Miclaus <antoniu.miclaus@analog.com>
Link: https://lore.kernel.org/r/20231026103413.27800-2-antoniu.miclaus@analog.com
[groeck: Fixed up documentation warning]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Accessing virtual registers is very inefficient, so pwm map values
should be cached when possible, else userspace could effectively do
a DOS attack by reading pwm map values in a while loop.
Use the regmap cache to cache those values.
Tested on a Fujitsu Esprimo P720.
Signed-off-by: Armin Wolf <W_Armin@gmx.de>
Link: https://lore.kernel.org/r/20230907052639.16491-4-W_Armin@gmx.de
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
POWER-Z is a series of devices to monitor power characteristics of
USB-C connections and display those on a on-device display.
Some of the devices, notably KM002C and KM003C, contain an additional
port which exposes the measurements via USB.
This is a driver for this monitor port.
It was developed and tested with the KM003C.
Signed-off-by: Thomas Weißschuh <linux@weissschuh.net>
Link: https://lore.kernel.org/r/20230902-powerz-v4-1-7ec2c1440687@weissschuh.net
[groeck:
Release urb after hwmon registration error;
Move priv->status initialization to correct place before reinit_completion
]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add base support for Renesas HS3001 temperature
and humidity sensors and its compatibles HS3002,
HS3003 and HS3004.
The sensor has a fix I2C address 0x44. The resolution
is fixed to 14bit (ref. Missing feature).
Missing feature:
- Accessing non-volatile memory: Custom board has no
possibility to control voltage supply of sensor. Thus,
we cannot send the necessary control commands within
the first 10ms after power-on.
Signed-off-by: Andre Werner <andre.werner@systec-electronic.com>
Link: https://lore.kernel.org/r/20230725042207.22310-2-andre.werner@systec-electronic.com
[groeck: Cosmetic documentation fixup; added documentation to index;
replaced probe_new with probe dropped unused variable]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
SMM665 and related chips are power controller/sequencer chips from
Summit Microelectronics. The company was acquired by Qualcomm in 2012,
and support for the chip series stopped.
The chips are long since gone from active use, making the driver
unsupportable and just consuming space and compile time. Remove it.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Hewlett-Packard (and some HP Compaq) business-class computers report
hardware monitoring information via WMI. This driver exposes that
information to hwmon.
Initial support is provided for temperature, fan speed, and intrusion
sensor types. Provisional support is provided for voltage and current
sensor types.
HP's WMI implementation permits many other types of numeric sensors.
Therefore, a debugfs interface is also provided to enumerate and
inspect all numeric sensors visible on the WMI side. This should
facilitate adding support for other sensor types in the future.
Tested on a HP Z420, a HP EliteOne 800 G1, and a HP Compaq Elite 8300
SFF.
Note that provisionally supported sensor types are untested and seem
to be rare-to-nonexistent in the wild, having been encountered
neither on test systems nor in ACPI dumps from the Linux Hardware
Database. They are included because their popularity in general makes
their presence on past or future HP systems plausible and because no
doubt exists as to how the sensors themselves would be represented in
WMI (alarm attributes will need to wait for hardware to be located).
A 2005 HP whitepaper gives the relevant sensor object MOF definition
and sensor value scaling calculation, and both this driver and the
official HP Performance Advisor utility comply with them (confirmed
in the latter case by reverse engineering).
Link: https://h20331.www2.hp.com/hpsub/downloads/cmi_whitepaper.pdf
Signed-off-by: James Seo <james@equiv.tech>
Link: https://lore.kernel.org/r/20230522115645.509701-1-james@equiv.tech
[groeck: Set error return value for intrusion writes to -EINVAL.
Always accept writes of 0 even if there was no intrusion. ]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
MAX31827 is a low-power temperature switch with I2C interface.
The device is a ±1°C accuracy from -40°C to +125°C
(12 bits) local temperature switch and sensor with I2C/SM-
Bus interface. The combination of small 6-bump wafer-lev-
el package (WLP) and high accuracy makes this temper-
ature sensor/switch ideal for a wide range of applications.
Signed-off-by: Daniel Matyas <daniel.matyas@analog.com>
Link: https://lore.kernel.org/r/20230524160131.14081-2-daniel.matyas@analog.com
[groeck: Improved define alignment, return -EINVAL after bad user input,
fixed up compatible statement]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Pull MFD updates from Lee Jones:
"Core Framework:
- Change MFD support status from Supported to Maintained
New Drivers:
- Add support for the Intel Platform Management Component Interface
(PMCI)
Removed Drivers:
- HTC PASIC3 LED/DS1WM
- Toshiba T7L66XB, TC6387XB and TC6393XB TMIO
New Device Support:
- Add support for N6000 Flash to Intel M10 BMC PMCI
- Add support for Lenovo Yoga Tab 3 to Intel CHTWC PMIC
New Functionality:
- Provide Reset support to Syscon
Fix-ups:
- Explicitly provide missing include files
- Pass platform type data/info via the SPI/I2C/DT registration
strategy
- Lots of DT documentation / adaptions
- Replace scnprintf() with preferred sysfs_emit()
- Remove unused / superfluous code
- Fix some trivial whitesspace / spelling / grammatical issues
- Replace pm_power_off with new and improved
register_sys_off_handler() API
Bug Fixes:
- Reintroduce RK808-clkout registration - fixing Wi-Fi and Bluetooth
- Repair the order of AXPxxx IRQ PEK RISE/FALL definitions
- Refuse to build CS5535 on unsupported UML architectures
- Fix memory leaks in error return paths
- Prevent refcount leaks in error return paths"
* tag 'mfd-next-6.3' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd: (40 commits)
dt-bindings: mfd: qcom,tcsr: Add compatible for IPQ5332
dt-bindings: mfd: Add NXP BBNSM
mfd: ntxec: Add version number for EC in Tolino Vision
dt-bindings: mfd: syscon: Add mt8365-syscfg
mfd: Remove toshiba tmio drivers
mfd: arizona: Use pm_runtime_resume_and_get() to prevent refcnt leak
mfd: syscon: Allow reset control for syscon devices
dt-bindings: mfd/syscon: Add resets property
dt-bindings: mfd: syscon: Add amd,pensando-elba-syscon compatible
dt-bindings: mfd: qcom,tcsr: Add compatible for MSM8226
mfd: simple-mfd-i2c: Fix incoherent comment regarding DT registration
mfd: axp20x: Switch to the sys-off handler API
mfd: core: Spelling s/compement/complement/
mfd: max8925: Remove the unused function irq_to_max8925()
mfd: qcom-pm8xxx: Remove set but unused variable 'rev'
dt-bindings: mfd: syscon: Document GXP register compatible
mfd: twl4030-power: Drop empty platform remove function
mfd: twl: Fix TWL6032 phy vbus detection
mfd: pcf50633-adc: Fix potential memleak in pcf50633_adc_async_read()
MAINTAINERS: Move MFD from a Supported to Maintaied state
...
Pull hwmon updates from Guenter Roeck:
"New drivers:
- Infineon TDA38640 Voltage Regulator
- NXP MC34VR500 PMIC
- GXP fan controller
- MPQ7932 Power Management IC
New chip or board support added to existing drivers:
- it87: IT87952E; also other cleanup/improvements
- intel-m10-bmc-hwmon: N6000
- pmbus/max16601: MAX16600
- aquacomputer_d5next: Aquacomputer Aquastream Ultimate, Aquacomputer
Poweradjust 3, Aquacomputer Aquaero
- nct6775: Support for B650/B660/X670 ASUS boards
- oxp-sensors: AYANEO AIR and AIR Pro
Other notable changes:
- Various kernel documentation fixes
- Various devicetree bindings fixes
- Explicitly deprecated [devm_]hwmon_device_register_with_groups
- ftsteutates: Support for fanX_fault and other cleanup
- ltc2945: Support for setting shunt resistor and other cleanup/fixes
- coretemp: Avoid RDMSR interrupts to isolated CPUs, and simplify
platform device handling
... and various other minor cleanups and fixes"
* tag 'hwmon-for-v6.3' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging: (66 commits)
hwmon: Deprecate [devm_]hwmon_device_register_with_groups
hwmon: (mlxreg-fan) Return zero speed for broken fan
hwmon: (gxp-fan-ctrl) use devm_platform_get_and_ioremap_resource()
hwmon: (aquacomputer_d5next) Add support for Aquacomputer Aquastream Ultimate
hwmon: (aquacomputer_d5next) Add support for Aquacomputer Poweradjust 3
hwmon: (iio_hwmon) use dev_err_probe
hwmon: intel-m10-bmc-hwmon: Add N6000 sensors
Docs/hwmon/index: Add missing SPDX License Identifier
hwmon: (it87) Updated documentation for recent updates to it87
hwmon: (it87) Add new chipset IT87952E
hwmon: (it87) Allow multiple chip IDs for force_id
hwmon: (it87) Add chip_id in some info message
hwmon: (it87) List full chip model name
hwmon: (it87) Disable configuration exit for certain chips
hwmon: (it87) Allow disabling exiting of configuration mode
Documentation: hwmon: correct spelling
hwmon: (pmbus/max16601) Add support for MAX16600
hwmon: (ltc2945) Allow setting shunt resistor
hwmon: (ltc2945) Handle error case in ltc2945_value_store
hwmon: (ltc2945) Add devicetree match table
...
The GXP SoC can support up to 16 fans through the interface provided by
the CPLD. The current support is limited to 8 fans. The fans speeds are
controlled via 8 different PWMs which can vary in value from 0-255. The
fans are also capable of reporting if they have failed to the CPLD which
in turn reports the status to the GXP SoC.
Signed-off-by: Nick Hawkins <nick.hawkins@hpe.com>
Link: https://lore.kernel.org/r/20230103203654.59322-2-nick.hawkins@hpe.com
[groeck: Improved alignment of defined, added missing include linux/bits.h]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The s3c adc driver was removed along with the s3c24xx platform, so the
hwmon driver is orphaned and can be removed.
Acked-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Sensors driver for OXP Handhelds from One-Netbook that expose fan reading
and control via hwmon sysfs.
As far as I could gather all OXP boards have the same DMI strings and
they can be told appart only by the boot cpu vendor (Intel/AMD).
Currently only AMD boards are supported since Intel have different EC
registers and values to read/write.
Fan control is provided via pwm interface in the range [0-255]. AMD
boards have [0-100] as range in the EC, the written value is scaled to
accommodate for that.
Signed-off-by: Joaquín Ignacio Aramendía <samsagax@gmail.com>
Link: https://lore.kernel.org/r/20221104140659.593608-1-samsagax@gmail.com
[groeck: Removed misleading comment about module_platform_driver()]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Switch the jc42 driver to use an I2C regmap to access the registers.
Also move over to regmap's built-in caching instead of adding a
custom caching implementation. This works for JC42_REG_TEMP_UPPER,
JC42_REG_TEMP_LOWER and JC42_REG_TEMP_CRITICAL as these values never
change except when explicitly written. The cache For JC42_REG_TEMP is
dropped (regmap can't cache it because it's volatile, meaning it can
change at any time) as well for simplicity and consistency with other
drivers.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Link: https://lore.kernel.org/r/20221023213157.11078-2-martin.blumenstingl@googlemail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
This driver utilises a WMI interface found in AMD 500 series ASUS boards,
to read EC registers. But it turned out that ASUS abandoned the
interface, as it disappeared from Intel 600 series boards. Additionally,
the WMI interface was incredibly slow. Therefore this driver was deprecated
in favor of the asus_ec_sensors driver, which supports more boards, more
sensors, and is faster.
Signed-off-by: Eugene Shalygin <eugene.shalygin@gmail.com>
Link: https://lore.kernel.org/r/20220720072016.102086-2-eugene.shalygin@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
NE1618 is similar to NE1617 but supports manufacturer and chip ID
registers as well as 11 bit external temperature resolution.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
NCT218 is compatible to NCT72 and NCT214. It also supports PEC (packet
error checking). Similar to NCT72 and NCT214, PEC support is undocumented.
Unlike NCT214 and NCT72, NCT218 does not support the undocumented secondary
chip and manufacturer ID registers at 0x3e and 0x3f and returns 0x00 when
reading those registers. The value for the chip revision register is not
documented but was observed to be 0xca. Use that information to improve
chip detection accuracy.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
NCT214 and NCT72 are compatible to ADT7461/ADT7461A but have full
PEC (packet error checking) support. PEC support is undocumented.
Both chips support the undocumented secondary chip and manufacturer
ID registers at 0x3e and 0x3f, and return 0x61 as chip ID. Use this
information to improve the accuracy of chip detection code.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Unlike ADM1023 and compatible chips, NCT210 does not support a temperature
offset register. A real chip was found to have a chip revision of 0x3f.
Use it to detect NCT210 explicitly.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
All chips supported by the ADM1021 driver are also supported by the LM90
driver. Make that support official.
After this change, the adm1021 driver is only needed if the lm90 driver
is disabled. Also, the adm1021 driver misdetects a variety of chips as
MAX1617A, which is unwanted if any of those chips is in the system.
For this reason. make the adm1021 driver dependent on !SENSORS_LM90 to
show that it is not needed if the lm90 driver is enabled, and to avoid
misdetection if a chip supported by the lm90 driver is in the system.
Devicetree nodes are not added for the added chips since it is quite
unlikely that such old chips will ever be used in a devicetree based
system. They can be added later if needed.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Both chips are quite similar to other chips of this series, so add
support for them to the lm90 driver. Also mention ON Semiconductor NCT210,
which is pin and register compatible to ADM1021A.
None of the chips support the secondary manufacturer and chip ID registers
at 0x3e and 0x3f, but return 0 when reading from those registers.
Use that information to improve the accuracy of chip detection code.
Devicetree nodes are not added for the added chips since it is quite
unlikely that such old chips will ever be used in a devicetree based
system. They can be added later if needed.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
MAX1617 and LM84 are stripped-down versions of LM90, so they can easily
be supported by the LM90 driver. The most difficult part is chip detection,
since those old chips do not support manufacturer ID or chip ID registers.
The "alarms" attribute is enabled for both chips to match the functionality
of the adm1021 driver. Chip detection was improved and is less prone to
misdetection than the chip detection in the adm1021 driver.
Devicetree nodes are not added for the added chips since it is quite
unlikely that such old chips will ever be used in a devicetree based
system. They can be added later if needed.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
MAX6642 is a reduced version of LM90 with no low limits and no conversion
rate register. Its alert functionality is broken, similar to many other
chips supported by the lm90 driver.
After this change, the stand-alone max6642 driver is only needed if the
lm90 driver is disabled. Make it dependent on SENSORS_LM90=n to show that
it is not needed if the lm90 driver is enabled.
A devicetree node is not added for this chip since it is quite unlikely
that such an old chip will ever be used in a devicetree based system.
It can be added later if needed.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
ADT7481, ADT7482, and ADT7483 are similar to ADT7461, but support two
external temperature sensors, similar to MAX6695/6696. They support an
extended temperature range similar to ADT7461. Registers for the second
external channel can be accessed directly or by using the same method as
used by MAX6695/6696. For simplicity, the access method implemented for
MAX6695/6696 is used.
The chips support PEC (packet error checking). Set the PEC feature flag
and let the user decide if it should be enabled or not (it is by default
disabled).
Even though it is only documented for ADT7483, all three chips support a
secondary manufacturer ID register at 0x3e and a chip ID register at 0x3f.
Use the contents of those registers register for improved chip detection
accuracy. Add the same check to the ADT7461A detection code since this chip
also supports the same (undocumented) registers.
Devicetree nodes are not added for the added chips since it is quite
unlikely that such old chips will ever be used in a devicetree based
system. They can be added later if needed.
Reviewed-by: Slawomir Stepien <sst@poczta.fm>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
This driver provides an i2c I/O mechanism for the core nct6775 driver,
as might be used by a BMC. Because the Super I/O chip is shared with
the host CPU in such a scenario (and the host should ultimately be in
control of it), the i2c driver is strictly read-only to avoid
interfering with any usage by the host (aside from the bank-select
register, which seems to be replicated for the i2c interface).
Signed-off-by: Zev Weiss <zev@bewilderbeest.net>
Tested-by: Renze Nicolai <renze@rnplus.nl>
Link: https://lore.kernel.org/r/20220428012707.24921-3-zev@bewilderbeest.net
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add support for the temperatur sensor and the fan controller on the
Microchip LAN966x SoC. Apparently, an Analog Bits PVT sensor is used
which can measure temperature and process voltages. But only a forumlae
for the temperature sensor is known. Additionally, the SoC support a fan
tacho input as well as a PWM signal to control the fan.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20220401214032.3738095-5-michael@walle.cc
[groeck: Added missing reference in Documentation/hwmon/index.rst]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Extend aquacomputer_d5next driver to expose hardware
temperature sensors of the Aquacomputer Farbwerk RGB controller, which
communicates through a proprietary USB HID protocol.
Four temperature sensors are available. Additionally, serial number and
firmware version are exposed through debugfs.
Also, add Jack Doan to MAINTAINERS for this driver.
Signed-off-by: Jack Doan <me@jackdoan.com>
Signed-off-by: Aleksa Savic <savicaleksa83@gmail.com>
Link: https://lore.kernel.org/r/YmTcrq8Gzel0zYYD@jackdesk
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Until now, only the temperature sensors where exported thru
the thermal subsystem. Export the fans as "dell-smm-fan[1-3]" too
to make them available as cooling devices.
Also update Documentation and fix a minor issue with the alphabetic
ordering of the includes.
Signed-off-by: Armin Wolf <W_Armin@gmx.de>
Link: https://lore.kernel.org/r/20220410163935.7840-1-W_Armin@gmx.de
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
