Commit 0c22ed0f authored by Jakub Kicinski's avatar Jakub Kicinski
Browse files

Merge branch 'remove-a-number-of-isa-and-pcmcia-ethernet-drivers' 

Andrew Lunn says:

====================
Remove a number of ISA and PCMCIA Ethernet drivers

These old drivers have not been much of a Maintenance burden until
recently. Now there are more newbies using AI and fuzzers finding
issues, resulting in more work for Maintainers. Fixing these old
drivers make little sense, if it is not clear they have users.

These mostly ISA and PCMCIA Ethernet devices, mostly from the last
century, a couple from 2001 or 2002. It seems unlikely they are still
used. However, remove them one patch at a time so they can be brought
back if somebody still has the hardware, runs modern kernels and wants
to take up the roll of driver Maintainer.
====================

Link: https://patch.msgid.link/20260422-v7-0-0-net-next-driver-removal-v1-v2-0-08a5b59784d5@lunn.ch


Signed-off-by: default avatarJakub Kicinski <kuba@kernel.org>
parents fc5f996b 15d07f9e

Documentation/.renames.txt

+0 −2
Original line number Diff line number Diff line
@@ -786,7 +786,6 @@ networking/altera_tse networking/device_drivers/ethernet/altera/altera_tse 
networking/bpf_flow_dissector bpf/prog_flow_dissector

networking/cxacru networking/device_drivers/atm/cxacru

networking/defza networking/device_drivers/fddi/defza

networking/device_drivers/3com/3c509 networking/device_drivers/ethernet/3com/3c509

networking/device_drivers/3com/vortex networking/device_drivers/ethernet/3com/vortex

networking/device_drivers/amazon/ena networking/device_drivers/ethernet/amazon/ena

networking/device_drivers/aquantia/atlantic networking/device_drivers/ethernet/aquantia/atlantic
@@ -821,7 +820,6 @@ networking/device_drivers/microsoft/netvsc networking/device_drivers/ethernet/mi 
networking/device_drivers/netronome/nfp networking/device_drivers/ethernet/netronome/nfp

networking/device_drivers/pensando/ionic networking/device_drivers/ethernet/pensando/ionic

networking/device_drivers/qualcomm/rmnet networking/device_drivers/cellular/qualcomm/rmnet

networking/device_drivers/smsc/smc9 networking/device_drivers/ethernet/smsc/smc9

networking/device_drivers/stmicro/stmmac networking/device_drivers/ethernet/stmicro/stmmac

networking/device_drivers/ti/cpsw networking/device_drivers/ethernet/ti/cpsw

networking/device_drivers/ti/cpsw_switchdev networking/device_drivers/ethernet/ti/cpsw_switchdev

Documentation/networking/device_drivers/ethernet/3com/3c509.rst

deleted100644 → 0
+0 −249
Original line number Diff line number Diff line 
.. SPDX-License-Identifier: GPL-2.0



=============================================================================

Linux and the 3Com EtherLink III Series Ethercards (driver v1.18c and higher)

=============================================================================



This file contains the instructions and caveats for v1.18c and higher versions

of the 3c509 driver. You should not use the driver without reading this file.



release 1.0



28 February 2002



Current maintainer (corrections to):

  David Ruggiero <jdr@farfalle.com>



Introduction

============



The following are notes and information on using the 3Com EtherLink III series

ethercards in Linux. These cards are commonly known by the most widely-used

card's 3Com model number, 3c509. They are all 10mb/s ISA-bus cards and shouldn't

be (but sometimes are) confused with the similarly-numbered PCI-bus "3c905"

(aka "Vortex" or "Boomerang") series.  Kernel support for the 3c509 family is

provided by the module 3c509.c, which has code to support all of the following

models:



 - 3c509 (original ISA card)

 - 3c509B (later revision of the ISA card; supports full-duplex)

 - 3c589 (PCMCIA)

 - 3c589B (later revision of the 3c589; supports full-duplex)

 - 3c579 (EISA)



Large portions of this documentation were heavily borrowed from the guide

written the original author of the 3c509 driver, Donald Becker. The master

copy of that document, which contains notes on older versions of the driver,

currently resides on Scyld web server: http://www.scyld.com/.





Special Driver Features

=======================



Overriding card settings



The driver allows boot- or load-time overriding of the card's detected IOADDR,

IRQ, and transceiver settings, although this capability shouldn't generally be

needed except to enable full-duplex mode (see below). An example of the syntax

for LILO parameters for doing this::



    ether=10,0x310,3,0x3c509,eth0



This configures the first found 3c509 card for IRQ 10, base I/O 0x310, and

transceiver type 3 (10base2). The flag "0x3c509" must be set to avoid conflicts

with other card types when overriding the I/O address. When the driver is

loaded as a module, only the IRQ may be overridden. For example,

setting two cards to IRQ10 and IRQ11 is done by using the irq module

option::



   options 3c509 irq=10,11





Full-duplex mode

================



The v1.18c driver added support for the 3c509B's full-duplex capabilities.

In order to enable and successfully use full-duplex mode, three conditions

must be met:



(a) You must have a Etherlink III card model whose hardware supports full-

duplex operations. Currently, the only members of the 3c509 family that are

positively known to support full-duplex are the 3c509B (ISA bus) and 3c589B

(PCMCIA) cards. Cards without the "B" model designation do *not* support

full-duplex mode; these include the original 3c509 (no "B"), the original

3c589, the 3c529 (MCA bus), and the 3c579 (EISA bus).



(b) You must be using your card's 10baseT transceiver (i.e., the RJ-45

connector), not its AUI (thick-net) or 10base2 (thin-net/coax) interfaces.

AUI and 10base2 network cabling is physically incapable of full-duplex

operation.



(c) Most importantly, your 3c509B must be connected to a link partner that is

itself full-duplex capable. This is almost certainly one of two things: a full-

duplex-capable  Ethernet switch (*not* a hub), or a full-duplex-capable NIC on

another system that's connected directly to the 3c509B via a crossover cable.



Full-duplex mode can be enabled using 'ethtool'.



.. warning::



  Extremely important caution concerning full-duplex mode



  Understand that the 3c509B's hardware's full-duplex support is much more

  limited than that provide by more modern network interface cards. Although

  at the physical layer of the network it fully supports full-duplex operation,

  the card was designed before the current Ethernet auto-negotiation (N-way)

  spec was written. This means that the 3c509B family ***cannot and will not

  auto-negotiate a full-duplex connection with its link partner under any

  circumstances, no matter how it is initialized***. If the full-duplex mode

  of the 3c509B is enabled, its link partner will very likely need to be

  independently _forced_ into full-duplex mode as well; otherwise various nasty

  failures will occur - at the very least, you'll see massive numbers of packet

  collisions. This is one of very rare circumstances where disabling auto-

  negotiation and forcing the duplex mode of a network interface card or switch

  would ever be necessary or desirable.





Available Transceiver Types

===========================



For versions of the driver v1.18c and above, the available transceiver types are:



== =========================================================================

0  transceiver type from EEPROM config (normally 10baseT); force half-duplex

1  AUI (thick-net / DB15 connector)

2  (undefined)

3  10base2 (thin-net == coax / BNC connector)

4  10baseT (RJ-45 connector); force half-duplex mode

8  transceiver type and duplex mode taken from card's EEPROM config settings

12 10baseT (RJ-45 connector); force full-duplex mode

== =========================================================================



Prior to driver version 1.18c, only transceiver codes 0-4 were supported. Note

that the new transceiver codes 8 and 12 are the *only* ones that will enable

full-duplex mode, no matter what the card's detected EEPROM settings might be.

This insured that merely upgrading the driver from an earlier version would

never automatically enable full-duplex mode in an existing installation;

it must always be explicitly enabled via one of these code in order to be

activated.



The transceiver type can be changed using 'ethtool'.





Interpretation of error messages and common problems

----------------------------------------------------



Error Messages

^^^^^^^^^^^^^^



eth0: Infinite loop in interrupt, status 2011.

These are "mostly harmless" message indicating that the driver had too much

work during that interrupt cycle. With a status of 0x2011 you are receiving

packets faster than they can be removed from the card. This should be rare

or impossible in normal operation. Possible causes of this error report are:



   - a "green" mode enabled that slows the processor down when there is no

     keyboard activity.



   - some other device or device driver hogging the bus or disabling interrupts.

     Check /proc/interrupts for excessive interrupt counts. The timer tick

     interrupt should always be incrementing faster than the others.



No received packets

^^^^^^^^^^^^^^^^^^^



If a 3c509, 3c562 or 3c589 can successfully transmit packets, but never

receives packets (as reported by /proc/net/dev or 'ifconfig') you likely

have an interrupt line problem. Check /proc/interrupts to verify that the

card is actually generating interrupts. If the interrupt count is not

increasing you likely have a physical conflict with two devices trying to

use the same ISA IRQ line. The common conflict is with a sound card on IRQ10

or IRQ5, and the easiest solution is to move the 3c509 to a different

interrupt line. If the device is receiving packets but 'ping' doesn't work,

you have a routing problem.



Tx Carrier Errors Reported in /proc/net/dev

^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^





If an EtherLink III appears to transmit packets, but the "Tx carrier errors"

field in /proc/net/dev increments as quickly as the Tx packet count, you

likely have an unterminated network or the incorrect media transceiver selected.



3c509B card is not detected on machines with an ISA PnP BIOS.

^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^



While the updated driver works with most PnP BIOS programs, it does not work

with all. This can be fixed by disabling PnP support using the 3Com-supplied

setup program.



3c509 card is not detected on overclocked machines

^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^



Increase the delay time in id_read_eeprom() from the current value, 500,

to an absurdly high value, such as 5000.





Decoding Status and Error Messages

----------------------------------





The bits in the main status register are:



=====	======================================

value 	description

=====	======================================

0x01 	Interrupt latch

0x02 	Tx overrun, or Rx underrun

0x04 	Tx complete

0x08 	Tx FIFO room available

0x10 	A complete Rx packet has arrived

0x20 	A Rx packet has started to arrive

0x40 	The driver has requested an interrupt

0x80 	Statistics counter nearly full

=====	======================================



The bits in the transmit (Tx) status word are:



=====	============================================

value	description

=====	============================================

0x02	Out-of-window collision.

0x04	Status stack overflow (normally impossible).

0x08	16 collisions.

0x10	Tx underrun (not enough PCI bus bandwidth).

0x20	Tx jabber.

0x40	Tx interrupt requested.

0x80	Status is valid (this should always be set).

=====	============================================





When a transmit error occurs the driver produces a status message such as::



   eth0: Transmit error, Tx status register 82



The two values typically seen here are:



0x82

^^^^



Out of window collision. This typically occurs when some other Ethernet

host is incorrectly set to full duplex on a half duplex network.



0x88

^^^^



16 collisions. This typically occurs when the network is exceptionally busy

or when another host doesn't correctly back off after a collision. If this

error is mixed with 0x82 errors it is the result of a host incorrectly set

to full duplex (see above).



Both of these errors are the result of network problems that should be

corrected. They do not represent driver malfunction.





Revision history (this file)

============================



28Feb02 v1.0  DR   New; major portions based on Becker original 3c509 docs

Documentation/networking/device_drivers/ethernet/index.rst

+0 −2
Original line number Diff line number Diff line
@@ -10,7 +10,6 @@ Contents: 
.. toctree::

   :maxdepth: 2



   3com/3c509

   3com/vortex

   amazon/ena

   altera/altera_tse
@@ -52,7 +51,6 @@ Contents: 
   pensando/ionic

   pensando/ionic_rdma

   qualcomm/ppe/ppe

   smsc/smc9

   stmicro/stmmac

   ti/cpsw

   ti/cpsw_switchdev

Documentation/networking/device_drivers/ethernet/smsc/smc9.rst

deleted100644 → 0
+0 −48
Original line number Diff line number Diff line 
.. SPDX-License-Identifier: GPL-2.0



================

SMC 9xxxx Driver

================



Revision 0.12



3/5/96



Copyright 1996  Erik Stahlman



Released under terms of the GNU General Public License.



This file contains the instructions and caveats for my SMC9xxx driver.  You

should not be using the driver without reading this file.



Things to note about installation:



  1. The driver should work on all kernels from 1.2.13 until 1.3.71.

     (A kernel patch is supplied for 1.3.71 )



  2. If you include this into the kernel, you might need to change some

     options, such as for forcing IRQ.





  3.  To compile as a module, run 'make'.

      Make will give you the appropriate options for various kernel support.



  4.  Loading the driver as a module::



	use:   insmod smc9194.o

	optional parameters:

		io=xxxx    : your base address

		irq=xx	   : your irq

		ifport=x   :	0 for whatever is default

				1 for twisted pair

				2 for AUI  ( or BNC on some cards )



How to obtain the latest version?



FTP:

	ftp://fenris.campus.vt.edu/smc9/smc9-12.tar.gz

	ftp://sfbox.vt.edu/filebox/F/fenris/smc9/smc9-12.tar.gz





Contacting me:

    erik@mail.vt.edu

MAINTAINERS

+1 −1
Original line number Diff line number Diff line
@@ -137,7 +137,7 @@ T: git git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty.git 
F:	drivers/tty/serial/8250*

F:	include/linux/serial_8250.h









8390 NETWORK DRIVERS [WD80x3/SMC-ELITE, SMC-ULTRA, NE2000, 3C503, etc.]









8390 NETWORK DRIVERS [NE2000, 3C503, etc.]









L:	netdev@vger.kernel.org









S:	Orphan / Obsolete









F:	drivers/net/ethernet/8390/