dt-bindings: phy: Add Apple Type-C PHY

# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)

%YAML 1.2

---

$id: http://devicetree.org/schemas/phy/apple,atcphy.yaml#

$schema: http://devicetree.org/meta-schemas/core.yaml#

title: Apple Type-C PHY (ATCPHY)

maintainers:

  - Sven Peter <sven@kernel.org>

description: >

  The Apple Type-C PHY (ATCPHY) is a combined PHY for USB 2.0, USB 3.x,

  USB4/Thunderbolt, and DisplayPort connectivity via Type-C ports found in

  Apple Silicon SoCs.

  The PHY handles muxing between these different protocols and also provides the

  reset controller for the attached DWC3 USB controller.

  It is designed for USB4 operation and does not handle individual differential

  pairs as distinct DisplayPort lanes. Any reference to lane in this binding

  hence refers to two differential pairs (RX and TX) as used in USB terminology.

  In order to correctly setup these lanes for the various modes calibration

  values copied from Apple's firmware and converted to the format described

  below by our bootloader m1n1 are required. Without these only USB2 operation

  is possible.

allOf:

  - $ref: /schemas/usb/usb-switch.yaml#

$defs:

  apple,tunable:

    $ref: /schemas/types.yaml#/definitions/uint32-matrix

    items:

      items:

        - description: Register offset

        - description: Mask to be applied to the register value

        - description: Bits to be set after applying the mask

    description: >

      List of (register offset, mask, value) tuples copied from Apple's Device

      Tree by our bootloader m1n1 and used to configure the PHY. These values

      even vary for a single product/device and likely contain calibration

      values determined by Apple at manufacturing time.

      Unless otherwise noted these tunables are always applied to the core

      register region.

properties:

  compatible:

    oneOf:

      - items:

          - enum:

              - apple,t6000-atcphy

              - apple,t6020-atcphy

              - apple,t8112-atcphy

          - const: apple,t8103-atcphy

      - const: apple,t8103-atcphy

  reg:

    items:

      - description: Common controls for all PHYs (USB2/3/4, DisplayPort, TBT)

      - description: DisplayPort Alternate Mode PHY specific controls

      - description: Type-C PHY AXI to Apple Fabric interconnect controls

      - description: USB2 PHY specific controls

      - description: USB3 PIPE interface controls

  reg-names:

    items:

      - const: core

      - const: lpdptx

      - const: axi2af

      - const: usb2phy

      - const: pipehandler

  "#phy-cells":

    const: 1

  "#reset-cells":

    const: 0

  mode-switch: true

  orientation-switch: true

  power-domains:

    maxItems: 1

  ports:

    $ref: /schemas/graph.yaml#/properties/ports

    properties:

      port@0:

        $ref: /schemas/graph.yaml#/properties/port

        description: Outgoing connection to the SS port of the Type-C connector.

      port@1:

        $ref: /schemas/graph.yaml#/properties/port

        description: Incoming endpoint from the USB3 controller.

      port@2:

        $ref: /schemas/graph.yaml#/properties/port

        description: Incoming endpoint from the DisplayPort controller.

      port@3:

        $ref: /schemas/graph.yaml#/properties/port

        description: Incoming endpoint from the USB4/Thunderbolt controller.

  apple,tunable-common-a:

    $ref: "#/$defs/apple,tunable"

    description: >

      Common tunables required for all modes, applied before tunable-axi2af.

  apple,tunable-axi2af:

    $ref: "#/$defs/apple,tunable"

    description: >

      AXI to Apple Fabric tunables, required for all modes. Unlike all other

      tunables these are applied to the axi2af region.

  apple,tunable-common-b:

    $ref: "#/$defs/apple,tunable"

    description: >

      Common tunables required for all modes, applied after tunable-axi2af.

  apple,tunable-lane0-usb:

    $ref: "#/$defs/apple,tunable"

    description: USB3 tunables for lane 0.

  apple,tunable-lane1-usb:

    $ref: "#/$defs/apple,tunable"

    description: USB3 tunables for lane 1.

  apple,tunable-lane0-cio:

    $ref: "#/$defs/apple,tunable"

    description: USB4/Thunderbolt ("Converged IO") tunables for lane 0.

  apple,tunable-lane1-cio:

    $ref: "#/$defs/apple,tunable"

    description: USB4/Thunderbolt ("Converged IO") tunables for lane 1.

  apple,tunable-lane0-dp:

    $ref: "#/$defs/apple,tunable"

    description: >

      DisplayPort tunables for lane 0.

      Note that lane here refers to a USB RX and TX pair re-used for DisplayPort

      and not to an individual DisplayPort differential lane.

  apple,tunable-lane1-dp:

    $ref: "#/$defs/apple,tunable"

    description: >

      DisplayPort tunables for lane 1.

      Note that lane here refers to a USB RX and TX pair re-used for DisplayPort

      and not to an individual DisplayPort differential lane.

required:

  - compatible

  - reg

  - reg-names

  - "#phy-cells"

  - "#reset-cells"

  - orientation-switch

  - mode-switch

  - power-domains

  - ports

additionalProperties: false

examples:

  - |

    phy@83000000 {

      compatible = "apple,t8103-atcphy";

      reg = <0x83000000 0x4c000>,

            <0x83050000 0x8000>,

            <0x80000000 0x4000>,

            <0x82a90000 0x4000>,

            <0x82a84000 0x4000>;

      reg-names = "core", "lpdptx", "axi2af", "usb2phy",

                  "pipehandler";

      #phy-cells = <1>;

      #reset-cells = <0>;

      orientation-switch;

      mode-switch;

      power-domains = <&ps_atc0_usb>;

      ports {

        #address-cells = <1>;

        #size-cells = <0>;

        port@0 {

          reg = <0>;

          endpoint {

            remote-endpoint = <&typec_connector_ss>;

          };

        };

        port@1 {

          reg = <1>;

          endpoint {

            remote-endpoint = <&dwc3_ss_out>;

          };

        };

        port@2 {

          reg = <2>;

          endpoint {

            remote-endpoint = <&dcp_dp_out>;

          };

        };

        port@3 {

          reg = <3>;

          endpoint {

            remote-endpoint = <&acio_tbt_out>;

          };

        };

      };

    };

F:	Documentation/devicetree/bindings/nvmem/apple,efuses.yaml

F:	Documentation/devicetree/bindings/nvmem/apple,spmi-nvmem.yaml

F:	Documentation/devicetree/bindings/pci/apple,pcie.yaml

F:	Documentation/devicetree/bindings/phy/apple,atcphy.yaml

F:	Documentation/devicetree/bindings/pinctrl/apple,pinctrl.yaml

F:	Documentation/devicetree/bindings/power/apple*

F:	Documentation/devicetree/bindings/power/reset/apple,smc-reboot.yaml