Merge series from Andreas Kemnade <andreas@kemnade.info>:
Add a driver for the TPS65185 regulator which provides the
comparatively high voltages needed for electronic paper displays.
Datasheet for the TPS65185 is at https://www.ti.com/lit/gpn/tps65185
To simplify things, include the hwmon part directly which is only
one temperature sensor and there are no other functions besides regulators
in this chip.
Add a driver for the TPS65185 regulator. Implement handling of the various
gpio pins. Because the PWRUP (=enable) pin functionality can be achieved
by just using two bits instead, just ensure that it is set to a stable
value.
Implement the pair of symmetric LDOs as a single regulator because they
share a single voltage set register. As the VCOM regulator sits behind that
machinery, just define that one as a supply.
For simplicity, just add the temperature sensor (depending on external NTC)
directly.
There is a mechanism to measure some kick-back voltage during a defined EPD
operation, to calibrate the VCOM voltage setting and store that
non-volatile in the chip to be the power up default setup. That is not
implemented yet in the driver, but that also means that there is a
non-factory default value in these registers after power-up.
Tested-by: Josua Mayer <josua.mayer@jm0.eu>
Signed-off-by: Andreas Kemnade <andreas@kemnade.info>
Link: https://patch.msgid.link/20260102-tps65185-submit-v3-2-23bda35772f2@kemnade.info
Signed-off-by: Mark Brown <broonie@kernel.org>
Add support for the Maxim Integrated MAX77675 PMIC regulator.
The MAX77675 is a compact, highly efficient SIMO (Single Inductor Multiple Output)
power management IC that provides four programmable buck-boost switching regulators
with only one inductor. It supports up to 700mA total output current and operates
from a single-cell Li-ion battery.
An integrated power-up sequencer and I2C interface allow flexible startup
configuration and runtime control.
Signed-off-by: Joan Na <joan.na@analog.com>
Link: https://patch.msgid.link/20251207032907.4850-3-joan.na@analog.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Merge series from Krzysztof Kozlowski <krzysztof.kozlowski@oss.qualcomm.com>:
Use container_of_const(), which is preferred over container_of(), when
the argument 'ptr' and returned pointer are already const, for better
code safety and readability.
Some drivers already have const everywhere, so container_of_const can be
directly used. In few other drivers, the final pointer can be constified
that way.
Add a driver for the FP9931/JD9930 regulator. Implement handling of the PG
(power good), TS_EN (temperature sensor enable), and EN (enable regulators)
pins. Implement the pair of symmetric LDOs as a single regulator because
they share a single voltage set register. For simplicity, just add the
temperature sensor (depending on external NTC) directly.
Limitations:
- As these regulators are controlled together with the VCOM regulator via
the EN pin, some kind of management must be in place. As the enable op
is not called when the regulator is already enabled, simple refcounting
seems not to work to avoid clearing EN when one regulator is still
enabled. As these regulators are typically used together, this
limitation should not hurt hard, just provide the is_enabled op.
- As the VCOM step is quite odd (5V/255 steps), rounding is needed.
Due to some limitations in the regulator core, the max/min voltages in
the devicetree must match the idea of the driver how to round things
exactly.
- Night mode is not implemented, so only the FP9931 compatible is needed in
the driver, there is no REGULATOR_MODE_NIGHT and no clear definition in
the datasheet what it does, also the XON pin which seems to be an input
related to that night mode is not used.
Signed-off-by: Andreas Kemnade <andreas@kemnade.info>
Link: https://patch.msgid.link/20251115-fp9931-submit-v3-3-92f5d0772b68@kemnade.info
Signed-off-by: Mark Brown <broonie@kernel.org>
Merge series from AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>:
This series adds support for three new MediaTek PMICs: MT6316, MT6363
and MT6373 and their variants - used in board designs featuring the
MediaTek MT8196 Chromebook SoC, or the MT6991 Dimensity 9400 Smartphone
SoC.
In particular, MT6316 is a regulator, but the MT6363 and MT6373 PMICs
are multi-function devices, as they have and expose multiple sub-devices;
moreover, some of those also contain an interrupt controller, managing
internal IPs interrupts: for those, a chained interrupt handler is
registered, which parent is the SPMI controller itself.
This series adds support for all of the MT6316 regulator variants and
for MT6363, MT6373 SPMI PMICs and their interrupt controller.
Add a driver for the regulators found on all types of the MediaTek
MT6316 SPMI PMIC, fully controlled by SPMI interface and featuring
four step down DCDC (buck) converters.
In particular, this includes support for:
- MT6316(BP/VP): 2+2 Phase (Phase 1: buck1+2, Phase 2: buck3+4)
- MT6316(CP/HP/KP): 3+1 Phase (Phase 1: buck1+2+4, Phase 2: buck3)
- MT6316(DP/TP): 4+0 Phase (Single phase, buck1+2+3+4)
Please note that the set/clear registers for the enable bits are
not documented in the datasheet version that I used as reference,
but those are used in the downstream driver and I verified that
are actually working as expected.
Besides, it's also worth clearly mentioning that the MT6316 PMICs
voltage selector register uses a weird 9-bits Big Endian format,
for which a driver-private helper is provided.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://patch.msgid.link/20251027110527.21002-3-angelogioacchino.delregno@collabora.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Pull MFD updates from Lee Jones:
"This round of updates contains a fair amount of new device support, a
couple of fixes and some refactoring. The most notable additions
include new drivers for Loongson's Security Engine, RNG and TPM, new
drivers for TI's TPS6594 Power Button and BQ257xx Charger ICs.
The rest of the set provides a return value check fix and a
refactoring to use a more modern GPIO API for the VEXPRESS sysreg
driver, the removal of a deprecated IRQ ACK function from the MC13xxx
RTC driver and a new DT binding for the aforementioned TI BQ257xx
charger.
New Support & Features:
- Add a suite of drivers for the Loongson Security Engine, including
the core controller, a Random Number Generator (RNG) and Trusted
Platform Module (TPM) support.
- Introduce support for the TI TPS6594 PMIC's power button, including
the input driver, MFD cell registration, and a system power-off
handler.
- Add comprehensive support for the TI BQ257xx series of charger ICs,
including the core MFD driver and a power supply driver for the
charger functionality.
Improvements & Fixes:
- Check the return value of devm_gpiochip_add_data() in the VEXPRESS
sysreg driver to prevent potential silent failures.
Cleanups & Refactoring:
- Add a MAINTAINERS entry for the new Loongson Security Engine
drivers.
- Convert the VEXPRESS sysreg driver to use the modern generic GPIO
chip API.
Removals:
- Remove the deprecated and unused mc13xxx_irq_ack() function from
the MC13xxx RTC, input and touchscreen drivers.
Device Tree Bindings Updates:
- Add device tree bindings for the TI BQ25703A charger"
* tag 'mfd-next-6.18' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd: (69 commits)
mfd: simple-mfd-i2c: Add compatible string for LX2160ARDB
mfd: simple-mfd-i2c: Keep compatible strings in alphabetical order
dt-bindings: mfd: twl: Add missing sub-nodes for TWL4030 & TWL603x
dt-bindings: watchdog: Add SMARC-sAM67 support
dt-bindings: mfd: tps6594: Allow gpio-line-names
mfd: intel-lpss: Add Intel Wildcat Lake LPSS PCI IDs
mfd: 88pm886: Add GPADC cell
mfd: vexpress-sysreg: Use more common syntax for compound literals
mfd: rz-mtu3: Fix MTU5 NFCR register offset
mfd: max77705: Setup the core driver as an interrupt controller
mfd: cs42l43: Remove IRQ masking in suspend
mfd: cs42l43: Move IRQ enable/disable to encompass force suspend
mfd: ls2kbmc: Add Loongson-2K BMC reset function support
mfd: ls2kbmc: Introduce Loongson-2K BMC core driver
mfd: bd71828, bd71815: Prepare for power-supply support
dt-bindings: mfd: aspeed: Add AST2700 SCU compatibles
dt-bindings: mfd: Convert aspeed,ast2400-p2a-ctrl to DT schema
dt-bindings: mfd: fsl,mc13xxx: Add buttons node
dt-bindings: mfd: fsl,mc13xxx: Convert txt to DT schema
mfd: macsmc: Add "apple,t8103-smc" compatible
...
Add support for the regulators found in the SpacemiT P1 PMIC. This
PMIC provides 6 buck converters and 12 LDO regulators.
The PMIC is implemented as a multi-function device. These regulators
are probed based on this driver being named in a MFD cell in the simple
MFD I2C driver.
Signed-off-by: Alex Elder <elder@riscstar.com>
Link: https://patch.msgid.link/20250825172057.163883-4-elder@riscstar.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Merge series from Ivaylo Ivanov <ivo.ivanov.ivanov1@gmail.com>:
This patchset adds support for the max77838 PMIC. It's used on the Galaxy
S7 lineup of phones, and provides regulators for the display.
Merge series from Woodrow Douglass <wdouglass@carnegierobotics.com>:
I wrote this driver to read settings and state from the nxp pf530x
regulator. Please consider it for inclusion, any criticism is welcome.
Merge series from Joy Zou <joy.zou@nxp.com>:
Add binding document and driver.
Signed-off-by: Joy Zou <joy.zou@nxp.com>
---
Changes in v3:
binding part
- change regulator node names into lowercase.
- add more description for nxp,i2c-crc-enable.
- remove the unnecessary nxp,dvs-run/standby-voltage property.
These changes come from review comments:
https://lore.kernel.org/imx/e9f38e38-7df7-4d19-b5c0-2f18aeebcc78@kernel.org/
- add regulator-state-mem property for example.
driver part
- convert to use maple tree register cache.
- change of_match_ptr() name to lowercase since dt-binding changed.
- add more nxp,i2c-crc-enable description for commit message.
- remove the of_parse_cb and dvs from pf0900_regulators since the
unnecessary property nxp,dvs-run/standby-voltage removed.
- add set_suspend_enable/disable/voltage for the SW regulator_ops.
the run/standby voltage can be adjusted via the API which regulator
driver provides is recommended.
These changes come from binding review comments:
https://lore.kernel.org/imx/e9f38e38-7df7-4d19-b5c0-2f18aeebcc78@kernel.org/
- add bitfield.h header due to build issue.
- correct the sw4 id.
- add PF0900 prefix for short macro define in order to avoid duplication.
- merge the same mask define in order to simplify code.
- Link to v2: https://lore.kernel.org/r/20250721-b4-pf09-v2-v2-0-e2c568548032@nxp.com
Changes in v2:
binding part
- modify the binding file name to match compatible string.
- add one space for dt_binding_check warning.
- remove unnecessary quotes from "VAON".
- remove the unnecessary empty line.
- move unevaluatedProperties after the $ref.
- move additionalProperties after regulator type.
- remove unnecessary regulator description
driver part
- modify the copyright comment block to C++ style.
- add reg_read/write for regmap_bus.
- remove original pf0900_pmic_read/write.
- remove many regulator operations.
- use regmap_read replace pf0900_pmic_read.
- use regmap_update_bits and regmap_write_bits replace pf0900_pmic_write.
- move the code from pf0900.h to pf0900-regulator.c and delete the header file.
- remove unmask status interrupts and add unmask regulator interrupts.
- remove many interrupts check warning print from irq_handler.
- add notifier for regulator event.
- remove unused macro define.
- add PF0900 prefix for IRQ macro define in order to avoid duplication.
- use GENMASK() and BIT() to replace mask marco define
- remove redundant enum pf0900_chip_type.
- remove redundant print info and comments.
- add dvs property present check because this property is optional.
- remove ret == -EINVAL check from sw_set_dvs() function.
- Link to v1: https://lore.kernel.org/imx/20250617102025.3455544-1-joy.zou@nxp.com/
---
Joy Zou (2):
dt-bindings: regulator: add PF0900 regulator yaml
regulator: pf0900: Add PMIC PF0900 support
.../devicetree/bindings/regulator/nxp,pf0900.yaml | 163 ++++
drivers/regulator/Kconfig | 8 +
drivers/regulator/Makefile | 1 +
drivers/regulator/pf0900-regulator.c | 975 +++++++++++++++++++++
4 files changed, 1147 insertions(+)
---
base-commit: 84b92a499e7eca54ba1df6f6c6e01766025943f1
change-id: 20250714-b4-pf09-v2-91cdee6d1272
Best regards,
--
Joy Zou <joy.zou@nxp.com>
Add regulator for the 7" Raspberry Pi 720x1280 DSI panel based on ili9881.
This is the Raspberry Pi DSI Panel V2. The newer Raspberry Pi 5" and 7"
panels have a slightly different register map to the original one. Add a
new driver for this "regulator" chip, this time by exposing two GPIOs and
one PWM controller, both of which can be consumed by panel driver and
pwm-backlight respectively.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Link: https://patch.msgid.link/20250609000748.1665219-2-marek.vasut+renesas@mailbox.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Add support for TPS65214 regulators (bucks and LDOs) to the TPS65219
Regulator Driver as the TPS65214/TPS65214/TPS65219 PMIC devices have
significant register map overlap. TPS65214 is a Power Management IC with 3
Buck regulators (like TPS65215/TPS65219) and has 2 LDOs (like TPS65215).
Signed-off-by: Shree Ramamoorthy <s-ramamoorthy@ti.com>
Link: https://patch.msgid.link/20250425205736.76433-5-s-ramamoorthy@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Isolate all changes involving TPS65215 regulator desc and range resources.
- 'chipid' will identify which PMIC to support, and the corresponding
chip_data struct element to use in probe(). The chip_data struct is
helpful for any new PMICs added to this driver. The goal is to add future
PMIC info to necessary structs and minimize probe() function edits.
- The probe() will now loop through common (overlapping) regulators first,
then device-specific structs identified in the chip_data struct.
- Add TI TPS65215 PMIC to the existing platform_device_id struct, so the
regulator probe() can handle which PMIC chip_data information to use.
Signed-off-by: Shree Ramamoorthy <s-ramamoorthy@ti.com>
Link: https://patch.msgid.link/20250425205736.76433-3-s-ramamoorthy@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Support new PMIC PF9453, which is totally difference with PCA9450. So
create new file for it.
The PF9453 is a single chip Power Management IC (PMIC) specifically
designed for i.MX 91 processor. It provides power supply solutions for IoT
(Internet of Things), smart appliance, and portable applications where size
and efficiency are critical. The device provides four high efficiency
step-down regulators, three LDOs, one 400 mA load switch and 32.768 kHz
crystal oscillator driver.
Signed-off-by: Joy Zou <joy.zou@nxp.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Link: https://patch.msgid.link/20250314-pf9453-v5-2-ab0cf1f871b0@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Pull regulator fixes from Mark Brown:
"These two commits clean up the excessively loose dependencies for the
RZG2L USB VBCTRL regulator driver, ensuring it shouldn't prompt for
people who can't use it"
* tag 'regulator-fix-v6.11-merge-window' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator:
regulator: Further restrict RZG2L USB VBCTRL regulator dependencies
regulator: renesas-usb-vbus-regulator: Update the default
Pull MFD updates from Lee Jones:
"New Drivers:
- ROHM BD96801 Power Management IC
- Cirrus Logic CS40L50 Haptic Driver with Waveform Memory
- Marvell 88PM886 Power Management IC
New Device Support:
- Keyboard Backlight to ChromeOS Embedded Controller
- LEDs to ChromeOS Embedded Controller
- Charge Control to ChromeOS Embedded Controller
- HW Monitoring Service to ChromeOS Embedded Controller
- AUXADCs to MediaTek MT635{7,8,9} Power Management ICs
New Functionality:
- Allow Syscon consumers to supply their own Regmaps on registration
Fix-ups:
- Constify/staticise applicable data structures
- Remove superfluous/duplicated/unused sections
- Device Tree binding adaptions/conversions/creation
- Trivial; spelling, whitespace, coding-style adaptions
- Utilise centrally provided helpers and macros to aid
simplicity/duplication
- Drop i2c_device_id::driver_data where the value is unused
- Replace ACPI/DT firmware helpers with agnostic variants
- Move over to GPIOD (descriptor-based) APIs
- Annotate a bunch of __counted_by() cases
- Straighten out some includes
Bug Fixes:
- Ensure potentially asserted recent lines are deasserted during
initialisation
- Avoid "<module>.ko is added to multiple modules" warnings
- Supply a bunch of MODULE_DESCRIPTIONs to silence modpost warnings
- Fix Wvoid-pointer-to-enum-cast warnings"
* tag 'mfd-next-6.11' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd: (87 commits)
mfd: timberdale: Attach device properties to TSC2007 board info
mfd: tmio: Move header to platform_data
mfd: tmio: Sanitize comments
mfd: tmio: Update include files
mmc: tmio/sdhi: Fix includes
mfd: tmio: Remove obsolete io accessors
mfd: tmio: Remove obsolete platform_data
watchdog: bd96801_wdt: Add missing include for FIELD_*()
dt-bindings: mfd: syscon: Add APM poweroff mailbox
dt-bindings: mfd: syscon: Split and enforce documenting MFD children
dt-bindings: mfd: rk817: Merge support for RK809
dt-bindings: mfd: rk817: Fixup clocks and reference dai-common
dt-bindings: mfd: syscon: Add TI's opp table compatible
mfd: omap-usb-tll: Use struct_size to allocate tll
dt-bindings: mfd: Explain lack of child dependency in simple-mfd
dt-bindings: mfd: Dual licensing for st,stpmic1 bindings
mfd: omap-usb-tll: Annotate struct usbtll_omap with __counted_by
mfd: tps6594-core: Remove unneeded semicolon in tps6594_check_crc_mode()
mfd: lm3533: Move to new GPIO descriptor-based APIs
mfd: tps65912: Use devm helper functions to simplify probe
...
The ROHM BD96801 "Scalable PMIC" is an automotive grade PMIC which can
scale to different applications by allowing chaining of PMICs. The PMIC
also supports various protection features which can be configured either
to fire IRQs - or to shut down power outputs when failure is detected.
The driver implements basic voltage control and sending error
notifications.
NOTE:
The driver does not support doing configuration which require the PMIC
to be in STBY state. The omitted feature set includes setting safety
limit values, changing LDO voltages and controlling enable state for
some regulators.
Also, the ERRB IRQ is not handled.
Signed-off-by: Matti Vaittinen <mazziesaccount@gmail.com>
Reviewed-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/50cf02b046df218a21a0f9c4820531d821fc20d4.1719473802.git.mazziesaccount@gmail.com
Signed-off-by: Lee Jones <lee@kernel.org>
As per the RZ/G2L HW manual, VBUSEN can be controlled by the VBOUT
bit of the VBUS Control Register. This register is mapped in the reset
framework. The reset driver expose this register as regmap and instantiates
this driver. The consumer will use the regulator API to control the VBOUT
bit as the control need to be done in the atomic context.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Link: https://patch.msgid.link/20240616105402.45211-5-biju.das.jz@bp.renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The Qualcomm PM8008 is an I2C-controlled PMIC containing seven LDO
regulators.
The driver is based on a driver submitted by Satya Priya, but it has
been cleaned up and reworked to match the new devicetree binding which
no longer describes each regulator as a separate device.
This avoids describing internal details like register offsets in the
devicetree and allows for extending the implementation with features
like over-current protection without having to update the binding.
Specifically note that the regulator interrupts are shared between all
regulators.
Note that the secondary regmap is looked up by name and that if the
driver ever needs to be generalised to support regulators provided by
the primary regmap (I2C address) such information could be added to the
device-id table.
This also fixes the original implementation, which looked up regulators
by 'regulator-name' property rather than devicetree node name and which
prevented the regulators from being named to match board schematics.
Link: https://lore.kernel.org/r/1655200111-18357-8-git-send-email-quic_c_skakit@quicinc.com
Cc: Satya Priya Kakitapalli <quic_skakitap@quicinc.com>
Cc: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20240608155526.12996-12-johan+linaro@kernel.org
Signed-off-by: Lee Jones <lee@kernel.org>
Pull MFD updates from Lee Jones:
"New Device Support:
- Add support for X-Powers AXP717 PMIC to AXP22X
- Add support for Rockchip RK816 PMIC to RK8XX
- Add support for TI TPS65224 PMIC to TPS6594
New Functionality:
- Add Power Off functionality to Rohm BD71828
- Allow I2C SMBus access in Renesas RSMU
Fix-ups:
- Device Tree binding adaptions/conversions/creation
- Shift Intel support over to MSI interrupts
- Generify adding platform data away from being ACPI specific
- Use device core supplied attribute to register sysfs entries
- Replace hand-rolled functionality with generic APIs
- Utilise centrally provided helpers and macros
- Clean-up error handling
- Remove superfluous/duplicated/unused sections
- Trivial; spelling, whitespace, coding-style adaptions
- More Maple Tree conversions"
* tag 'mfd-next-6.10' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd: (44 commits)
dt-bindings: mfd: Use full path to other schemas
mfd: rsmu: support I2C SMBus access
dt-bindings: mfd: Convert lp873x.txt to json-schema
dt-bindings: mfd: aspeed: Drop 'oneOf' for pinctrl node
dt-bindings: mfd: allwinner,sun6i-a31-prcm: Use hyphens in node names
mfd: ssbi: Remove unused field 'slave' from 'struct ssbi'
mfd: kempld: Remove custom DMI matching code
mfd: cs42l43: Update patching revision check
dt-bindings: mfd: qcom: pm8xxx: Add pm8901 compatible
mfd: timberdale: Remove redundant assignment to variable err
dt-bindings: mfd: qcom,spmi-pmic: Add pbs to SPMI device types
dt-bindings: mfd: syscon: Add ti,am62p-cpsw-mac-efuse compatible
dt-bindings: mfd: qcom,tcsr: Add compatible for SDX75
mfd: axp20x: Convert to use Maple Tree register cache
mfd: bd71828: Remove commented code lines
mfd: intel-m10-bmc: Change staging size to a variable
dt-bindings: mfd: Add ROHM BD71879
mfd: Tidy Kconfig dependency's parentheses
mfd: ocelot-spi: Use spi_sync_transfer()
dt-bindings: mfd: syscon: Add missing simple syscon compatibles
...
