Commit a3b4a48f authored by Guillaume Stols's avatar Guillaume Stols Committed by Jonathan Cameron
Browse files

dt-bindings: iio: adc: adi,ad7606: normalize textwidth 



Normalize textwidth to 80 columns on the descriptions.

Acked-by: default avatarRob Herring (Arm) <robh@kernel.org>
Signed-off-by: default avatarGuillaume Stols <gstols@baylibre.com>
Signed-off-by: default avatarJonathan Cameron <Jonathan.Cameron@huawei.com>
parent 43ebc481

Documentation/devicetree/bindings/iio/adc/adi,ad7606.yaml

+24 −26
Original line number Diff line number Diff line
@@ -40,60 +40,58 @@ properties: 


  adi,conversion-start-gpios:

    description:

      Must be the device tree identifier of the CONVST pin.

      This logic input is used to initiate conversions on the analog

      input channels. As the line is active high, it should be marked

      GPIO_ACTIVE_HIGH.

      Must be the device tree identifier of the CONVST pin. This logic input is

      used to initiate conversions on the analog input channels. As the line is

      active high, it should be marked GPIO_ACTIVE_HIGH.

    maxItems: 1



  reset-gpios:

    description:

      Must be the device tree identifier of the RESET pin. If specified,

      it will be asserted during driver probe. As the line is active high,

      it should be marked GPIO_ACTIVE_HIGH.

      Must be the device tree identifier of the RESET pin. If specified, it will

      be asserted during driver probe. As the line is active high, it should be

      marked GPIO_ACTIVE_HIGH.

    maxItems: 1



  standby-gpios:

    description:

      Must be the device tree identifier of the STBY pin. This pin is used

      to place the AD7606 into one of two power-down modes, Standby mode or

      Must be the device tree identifier of the STBY pin. This pin is used to

      place the AD7606 into one of two power-down modes, Standby mode or

      Shutdown mode. As the line is active low, it should be marked

      GPIO_ACTIVE_LOW.

    maxItems: 1



  adi,first-data-gpios:

    description:

      Must be the device tree identifier of the FRSTDATA pin.

      The FRSTDATA output indicates when the first channel, V1, is

      being read back on either the parallel, byte or serial interface.

      As the line is active high, it should be marked GPIO_ACTIVE_HIGH.

      Must be the device tree identifier of the FRSTDATA pin.  The FRSTDATA

      output indicates when the first channel, V1, is being read back on either

      the parallel, byte or serial interface.  As the line is active high, it

      should be marked GPIO_ACTIVE_HIGH.

    maxItems: 1



  adi,range-gpios:

    description:

      Must be the device tree identifier of the RANGE pin. The polarity on

      this pin determines the input range of the analog input channels. If

      this pin is tied to a logic high, the analog input range is ±10V for

      all channels. If this pin is tied to a logic low, the analog input range

      is ±5V for all channels. As the line is active high, it should be marked

      Must be the device tree identifier of the RANGE pin. The polarity on this

      pin determines the input range of the analog input channels. If this pin

      is tied to a logic high, the analog input range is ±10V for all channels.

      If this pin is tied to a logic low, the analog input range is ±5V for all

      channels. As the line is active high, it should be marked

      GPIO_ACTIVE_HIGH.

    maxItems: 1



  adi,oversampling-ratio-gpios:

    description:

      Must be the device tree identifier of the over-sampling

      mode pins. As the line is active high, it should be marked

      GPIO_ACTIVE_HIGH.

      Must be the device tree identifier of the over-sampling mode pins. As the

      line is active high, it should be marked GPIO_ACTIVE_HIGH.

    maxItems: 3



  adi,sw-mode:

    description:

      Software mode of operation, so far available only for ad7616 and ad7606b.

      It is enabled when all three oversampling mode pins are connected to

      high level. The device is configured by the corresponding registers. If the

      adi,oversampling-ratio-gpios property is defined, then the driver will set the

      oversampling gpios to high. Otherwise, it is assumed that the pins are hardwired

      to VDD.

      It is enabled when all three oversampling mode pins are connected to high

      level. The device is configured by the corresponding registers. If the

      adi,oversampling-ratio-gpios property is defined, then the driver will set

      the oversampling gpios to high. Otherwise, it is assumed that the pins are

      hardwired to VDD.

    type: boolean



required: